Bonjour,
Après 1 an de développement, la team MSextra (James Murray et Ken Cuvler) viennent de mettre à disposition la version finale du firmware 1.3.1 pour les calculateurs MegaSquirt 3, MS3-Pro, MS3 module et MS3 gold.
Principaux changements depuis les version 1.2.4 :
Bug corrigés :
http://www.msextra.com/doc/auth.php?f=m ... 1.zip&l=fr
Assurez-vous de bien lire le fichier RELEASE-NOTES.txt inclut dans l'archive afin de connaitre les "GOTCHAS" lorsque vous mettez à jour un calculateur ayant un firmware précédent (typiquement 1.3.0, le dernier firmware stable pour MS3).
Sportivement,
Manu
Après 1 an de développement, la team MSextra (James Murray et Ken Cuvler) viennent de mettre à disposition la version finale du firmware 1.3.1 pour les calculateurs MegaSquirt 3, MS3-Pro, MS3 module et MS3 gold.
Principaux changements depuis les version 1.2.4 :
Bug corrigés :
- Typo causing GPS to trigger single event fuel cut.
- Many after-launch features broken on 2014-08-07, STATUS2_LAUNCH was not being used.
- Traction changes for perfect run and button modes.
- Fix timer rollover for boost delay.
- Fix table blend behavior with boost initial values table.
- Boost control "mid" output setting wasn't working.
- Alter phasing on 36-2+2 NGC 6-cyl
- Fix up ini bitfield errors (would have broken some settings on gen PWM, water inj)
- Fix Time-After-Spark (same issue as MS2)
- Fixed max VSS for launch and change logic for VSS flat-shift.
- Fix MPG calc (off by factor of 10)
- Fix CL idle getting "stuck" just after cranking.
- Fix flex fuel temperature calculation.
- EDIS sets "Full RPM sync"
- Average 1-cyl RPMs over two revs.
- Rename "closed/open" to "minimum/maximum" for boost and idle valve settings.
- Fix rogue pulses on MS3X secondaries for staging or dual-fuel.
- MS3X non-sequential staging uses expected number of outputs.
- Fix staging transition "saw-tooth" issue.
- Re-do staging duty calcs to work with sequential.
- Extend vssout_scale to 32bit.
- EGO "load above" setting allows negative numbers.
- Implement CAN TX timeout and reset.
- Allow up to 12 VVT teeth in ini.
- Swap phase on GM7X 6cyl.
- Remove "ability" to use +360 on trigger angle/offset to swap phase - not working.
- Add config error for unsupported 36-2-2-2 combinations
- Experimental non-linear spk cut for launch.
- Reduce serial timeout to 25ms - fixes Race Technology adapter for Megasquirt.
- VSS and SS sampled every 50ms instead of 100ms
- Use TS generated CLT, MAT GM calibrations. Use MAT for "GM calibration"
- ini tweaks
- Fix a couple of ini error that TS missed.
- Change defaults for ITB load.
- Fix TPSdot limits in ini.
- Extend AFR table limits in ini.
- ini
- capitalisation and consistency
- some units standardisation (gives some warnings on old MSQ load)
- remove GridHeight
http://www.msextra.com/doc/auth.php?f=m ... 1.zip&l=fr
Assurez-vous de bien lire le fichier RELEASE-NOTES.txt inclut dans l'archive afin de connaitre les "GOTCHAS" lorsque vous mettez à jour un calculateur ayant un firmware précédent (typiquement 1.3.0, le dernier firmware stable pour MS3).
Sportivement,
Manu
Le plaisir automobile commence à 4000 tours par minute, là ou un moteur diesel s’arrête.