Support officiel Megasquirt, Tech Edge WBO2, Tuner Pro, AutoSport Labs et Fenixecu 

  • MS3/Extra 1.3.1 stable pour MS3

  • Les firmwares et logiciels pour paramétrer, régler et utiliser votre MegaSquirt - MegaTune, Tuner Studio MS, MegaLog Viewer, MS Extra...
Les firmwares et logiciels pour paramétrer, régler et utiliser votre MegaSquirt - MegaTune, Tuner Studio MS, MegaLog Viewer, MS Extra...
 #3075  par Manu
 30 mai 2014 09:33
Bonjour,

Après 1 an de développement, la team MSextra (James Murray et Ken Cuvler) viennent de mettre à disposition la version finale du firmware 1.3.1 pour les calculateurs MegaSquirt 3, MS3-Pro, MS3 module et MS3 gold.

Principaux changements depuis les version 1.2.4 :

Bug corrigés :
  • Typo causing GPS to trigger single event fuel cut.
  • Many after-launch features broken on 2014-08-07, STATUS2_LAUNCH was not being used.
  • Traction changes for perfect run and button modes.
  • Fix timer rollover for boost delay.
  • Fix table blend behavior with boost initial values table.
  • Boost control "mid" output setting wasn't working.
  • Alter phasing on 36-2+2 NGC 6-cyl
  • Fix up ini bitfield errors (would have broken some settings on gen PWM, water inj)
  • Fix Time-After-Spark (same issue as MS2)
  • Fixed max VSS for launch and change logic for VSS flat-shift.
  • Fix MPG calc (off by factor of 10)
  • Fix CL idle getting "stuck" just after cranking.
  • Fix flex fuel temperature calculation.
  • EDIS sets "Full RPM sync"
Améliorations / nouvelles fonctions :
  • Average 1-cyl RPMs over two revs.
  • Rename "closed/open" to "minimum/maximum" for boost and idle valve settings.
  • Fix rogue pulses on MS3X secondaries for staging or dual-fuel.
  • MS3X non-sequential staging uses expected number of outputs.
  • Fix staging transition "saw-tooth" issue.
  • Re-do staging duty calcs to work with sequential.
  • Extend vssout_scale to 32bit.
  • EGO "load above" setting allows negative numbers.
  • Implement CAN TX timeout and reset.
  • Allow up to 12 VVT teeth in ini.
  • Swap phase on GM7X 6cyl.
  • Remove "ability" to use +360 on trigger angle/offset to swap phase - not working.
  • Add config error for unsupported 36-2-2-2 combinations
  • Experimental non-linear spk cut for launch.
  • Reduce serial timeout to 25ms - fixes Race Technology adapter for Megasquirt.
  • VSS and SS sampled every 50ms instead of 100ms
Changement internes / modifications mineures :
  • Use TS generated CLT, MAT GM calibrations. Use MAT for "GM calibration"
  • ini tweaks
  • Fix a couple of ini error that TS missed.
  • Change defaults for ITB load.
  • Fix TPSdot limits in ini.
  • Extend AFR table limits in ini.
  • ini
    - capitalisation and consistency
    - some units standardisation (gives some warnings on old MSQ load)
    - remove GridHeight
Vous pouvez télécharger ce firmware ici :
http://www.msextra.com/doc/auth.php?f=m ... 1.zip&l=fr

Assurez-vous de bien lire le fichier RELEASE-NOTES.txt inclut dans l'archive afin de connaitre les "GOTCHAS" lorsque vous mettez à jour un calculateur ayant un firmware précédent (typiquement 1.3.0, le dernier firmware stable pour MS3).

Sportivement,
Manu