Support officiel Megasquirt, Tech Edge WBO2, Tuner Pro, AutoSport Labs et Fenixecu 

  • Problème de concordance

  • Les firmwares et logiciels pour paramétrer, régler et utiliser votre MegaSquirt - MegaTune, Tuner Studio MS, MegaLog Viewer, MS Extra...
Les firmwares et logiciels pour paramétrer, régler et utiliser votre MegaSquirt - MegaTune, Tuner Studio MS, MegaLog Viewer, MS Extra...
 #4339  par electron
 15 août 2015 18:54
Bonjour à tous,

Je vous présente brièvement mon projet. J’utilise Megasquirt pour contrôler mon moteur monocylindre BMW G450X qui est dans une partie cycle type Moto3.

Voilà j’apprends peu à peu à utiliser Tuner Studio mais c’est loin d’être intuitif pour moi.
Le moteur a tourné avec cette gestion déjà plusieurs courses sans soucis aucun.
Mais voilà, le firmware a été mis à jour et TS aussi. Le moteur ne démarre pas. Tout mon équipement est ok, j’ai l’étincelle, l’injection…
Quand j’essaye d’ouvrir le fichier .msq qui gérait le moteur, j’ai des messages d’erreur.

Image

TS m’avertit que le fichier (anciennement créé) ne concorde pas avec le nouveau TS et m’avertit que :
Warning: MSQ Units Mismatch for idleadvance_delay! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim1! % TPS found in current configuration, % found in MSQ, values were not converted to new units.


Bref 78 erreurs.

J’ai sauvé ce fichier avec le nouveau TS et envoyer au calculateur mais mon moteur ne démarre toujours pas.

Pour info le fichier .msq qui fonctionnait avant avait pour définition :
Code : Tout sélectionner
<?xml version="1.0" encoding="ISO-8859-1"?>
<msq xmlns="http://www.msefi.com/:msq">
<bibliography author="[b]TunerStudio MS 2.0.6[/b] - EFI Analytics, Inc." tuneComment="<html>Point de restauration: Project close - <br>    <br>&#13;    &#13;&#13;    <p style="margin-top: 0">&#13;      <br>&#13;      <br>&#13;      &#13;    </p>&#13;    <br>&#13;  " writeDate="Sat May 17 08:59:19 CEST 2014"/>
<versionInfo fileFormat="4.0" firmwareInfo="[b]MS2/Extra release 3.2.4[/b] 20120901 22:00BST (c)KC/JSM/JB MS2" nPages="6" signature="MS2Extra Serial324 "/>
Et le nouveau que je sauvegarde avec le nouveau TS :
Code : Tout sélectionner
<?xml version="1.0" encoding="ISO-8859-1"?>
<msq xmlns="http://www.msefi.com/:msq">
<bibliography author="[b]TunerStudio MS(Beta) Lite! 2.6.19[/b] - EFI Analytics, Inc." tuneComment="<html>Point de restauration: Project close - <br>    <br>&#13;    &#13;&#13;    <p style="margin-top: 0">&#13;      <br>&#13;      <br>&#13;      &#13;    </p>&#13;    <br>&#13;  " writeDate="Wed Aug 12 19:03:45 CEST 2015"/>
<versionInfo fileFormat="4.0" firmwareInfo="" nPages="7" signature="[b]MS2Extra comms333e2[/b]"/>
Est-ce que quelqu’un peut m’aider ?

Merci d’avance.
Jérôme
 #4340  par electron
 15 août 2015 18:57
Comment dois-je faire pour convertir le fichier .msq pour qu'il soit compatible avec le nouveau firmware ?
 #4343  par Manu
 16 août 2015 21:23
Salut,

Déjà, puisque tu en là, je te conseille de mettre ta gestion à jour avec le dernier firmware 3.4.0 (et non le 3.3.3 avec lequel tu te bats). A faire la migration, autant utiliser les dernières versions disponibles !

Ensuite poste donc ton fichier MSQ en 3.2.4 et en 3.3.3, on y verra plus clair !

Mais ne t'affole pas à propos des messages d'erreur envoyés par tunerStudio MS. C'est juste des avertissement à propos des unités utilisés par tes 2 projets. TunerStudio gère très bien ce type de modifications seul et prends les décisions qu'il faut pour corriger tout cela !

Ainsi :
Code : Tout sélectionner
Warning: MSQ Units Mismatch for idleadvance_delay! s found in current configuration, sec found in MSQ, values were not converted to new units.
TunerStudio MS te signal que dans un projet la valeur idleadvance_delay est exprimée en s, et dans l'autre projet en sec :?: Bref, toujours en secondes quoi... C'est juste l’abréviation qui change !

A ce niveau là tu as aussi le choix de revenir en version 3.2.4 du firmware. Qu'est-ce qui a motivé la mise à jour du firmware ?

Sportivement,
Manu
 #4344  par electron
 16 août 2015 22:57
Bonsoir,

Merci pour votre réponse.

J'ai envoyé mon calculateur à une entreprise pour qu'on m'installe un adaptateur bluetooth et on m'a proposé de mettre à jour mon firmware par la même occasion. Je suis basé en Allemagne et il était géographiquement plus simple pour moi de traiter avec une entreprise allemande. Mais j'ai quelques difficultés à comprendre ses explications...

Fichier qui fonctionnait
http://www.partage-facile.com/FFORCD3LB ... 9.msq.html

Fichier sauvegardé avec l'update de TS
http://www.partage-facile.com/FZKYAN7LR ... n.msq.html
 #4346  par Manu
 17 août 2015 10:46
Mon anti-virus bloque partage-facile !
 #4350  par electron
 17 août 2015 19:48
Je viens de voir ça aussi dans mes avertissements :

Warning: MSQ Units Mismatch for EAESOCKPAbins! % TPS found in current configuration, kpa found in MSQ, values were not converted to new units.

Là c'est un peu plus problêmatique que la transformation de "s" en "sec" ? ça pourrait venir de ce type d'erreur ? Faut-il que je recalibrer chaque composant comme dans le tutoriel de mise en route ?

Je partage aussi mes messages d'erreurs
Code : Tout sélectionner
78 Warnings:
Warning: MSQ Units Mismatch for knk_tadv! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for amap_table2! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Disable"' for parameter: enable_pollADC is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for amap_table1! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Value in .msq '"5"' for parameter: can_poll_id is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:can_poll equal to the proposed Disabled
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:flexport equal to the proposed PA0
Warning: Value in .msq '"Remote Port3 Bit 0"' for parameter: knkport_remote is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Off"' for parameter: feature4_0vanos is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:spk_config_spka equal to the proposed Tachout
Warning: Value in .msq '"Disabled"' for parameter: AMCOption is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Local"' for parameter: flexFuelRemote is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for knk_trtd! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Master"' for parameter: can_poll_slave is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Off"' for parameter: spk_conf2_ngc is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for IACcrankxt! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Off"' for parameter: feature4_0mindwl is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Fuel&spark cut"' for parameter: RevLimOption is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:EAEOption equal to the proposed ON
Warning: Value in .msq '"PWM0"' for parameter: flexportRemote is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Local"' for parameter: knk_remote is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:rtbaroport equal to the proposed SPAREADC
Warning: Value in .msq '"Port Injection"' for parameter: injType is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:IdleCtl equal to the proposed 15-Minute IAC
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:ego2port equal to the proposed SPAREADC
Warning: Value in .msq '"On"' for parameter: feature4_0maxdwl is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Remote Port3 Bit 0"' for parameter: tsf_remote_port is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for EAEAWCKPAbins! % TPS found in current configuration, kpa found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Remote Port3 Bit 0"' for parameter: tss_remote_port is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Normal"' for parameter: boost_ctl_settings_invert is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for EAESOCKPAbins! % TPS found in current configuration, kpa found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Local"' for parameter: tsf_remote is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for smap_injadv3! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fc_ego_delay! s found in current configuration, seconds found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_targ_ramptime! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_close_delay! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_shift_open_time! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: baroCorrVals array size does not match the currently loaded configuration,
	rescaled .msq values to match configuration.
Warning: MSQ Units Mismatch for pwmidle_pid_wait_timer! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: baroCorrDelta array size does not match the currently loaded configuration,
	rescaled .msq values to match configuration.
Warning: Value in .msq '"Local"' for parameter: tss_remote is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:tacho_opt3f equal to the proposed IGN
Warning: Value in .msq '"78Hz"' for parameter: pwmidleset_hz is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Local"' for parameter: N20remote_input is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:launch_opt_pins equal to the proposed SPAREADC
Warning: MSQ Units Mismatch for RotarySplitLoad! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Remote Port1 Bits 0+1"' for parameter: N20remote_outport is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for smap_table1! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Value in .msq '"Rotary off"' for parameter: RotarySplitModeOn is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Disabled"' for parameter: RotarySplitModeRX8 is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Local"' for parameter: N20remote_output is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins2 equal to the proposed PT7+6
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins equal to the proposed Flex
Warning: Value in .msq '"Remote Port3 Bit 0"' for parameter: N20remote_inport is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for idleadvance_delay! s found in current configuration, sec found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim1! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: idleadvance_loads array size does not match the currently loaded configuration,
	rescaled .msq values to match configuration.
Warning: MSQ Units Mismatch for smap_injadv2! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for smap_injadv1! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:testop_coil equal to the proposed CoilA
Warning: Value in .msq '"Neither"' for parameter: test_addinj is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"Off"' for parameter: testmode is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: idleadvance_curve array size does not match the currently loaded configuration,
	rescaled .msq values to match configuration.
Warning: MSQ Units Mismatch for smap_table3! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:testop_inj equal to the proposed Neither
Warning: Value in .msq '"Off"' for parameter: iactestlock is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: Value in .msq '"run"' for parameter: iactest is of a type that is not compatible with the current firmware.This will be ignored, please correct manually.
Warning: MSQ Units Mismatch for fmap_trim1doz! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table3doz! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table1doz! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table1! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_table3! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim2! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim4! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim3! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim3doz! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim2doz! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fmap_trim4doz! % TPS found in current configuration, % found in MSQ, values were not converted to new units.
Merci d'avance ;)
 #4351  par Manu
 17 août 2015 20:17
Bonsoir,

Cela indique juste, sans avoir regardé les MSQ, que votre stratégie est passée de pression/régime à papillon/régime pour l'axe Y de l'enrichissement. Je regarderais au MSQ plus tard.

Sportivement,
Manu
 #4364  par electron
 19 août 2015 13:01
Merci.

Je ne pourrai pas voir votre réponse avant Dimanche, j'ai justement une course mais avec une autre moto du coup ! :)